Search results

peer-reviewed ; In recent years, the development of small and low power electronics has led to the deployment of Wireless Sensor Networks (WSNs), that are largely used in military and civil applications. Vibrational energy harvesting can be used to power these sensors in order to obviate the costs of battery replacement. Vibrational energy harvesters (VEHs) are devices that convert the kinetic energy present in the ambient into electrical energy using three principal transduction mechanisms: piezoelectric, electromagnetic or electrostatic. The investigation presented in this paper specifically aims to realize a device that converts vibrations from different ambient sources to electrical energy for powering autonomous wireless sensors. A "C-battery" scale (25.5 mm diameter by 57.45 mm long, 29.340 cm3 ) two Degree-of-Freedom (2-DoF) nonlinear electromagnetic energy harvester, which employs velocity amplification, is presented in this paper. Velocity amplification is achieved through sequential collisions between two free-moving masses, a primary (larger) and a secondary (smaller) mass. The nonlinearities are due to the use of multiple masses and the use of magnetic springs between the primary mass and the housing, and between the primary and secondary masses. Part A of this paper presents detailed experimental characterization of the system dynamics, while Part B describes the design and verification of the magnet/coil interaction for optimum prototype power output. The harvester is characterized experimentally under sinusoidal excitation for different geometrical configurations and also under the excitation of an air-compressor. The maximum output power generated under sinusoidal excitation of arms = 0.4 g is 1.74 mW across a resistive load of 9975 Ω, while the output rms voltage is 4.2 V. Under the excitation of the compressor, the maximum peak power across a load resistance of 8660 Ω is 1.37 mW, while the average power is 85.5 µW.

The technique of harvesting the energy from base structural vibration through a piezoelectric transducer attached at an appropriate location on the vibrating structure is gaining popularity in recent years. Although the amount of energy harvested depends on the type and magnitude of base excitation, the energy harvest under random excitation as compared to equivalent harmonic excitations is not yet well understood and is investigated in this paper through a cantilever energy harvester. Initially, the energy harvested under harmonic excitations is numerically simulated and experimentally validated under increasing base accelerations with different load resistances. Subsequently, the performance of this energy harvester is experimentally studied under random excitations. The results demonstrate that the harvested energy (a) reaches maximum value when the base excitation matches the natural frequency of the harvester, (b) increases with the increase in base accelerations irrespective of the type of excitation, and (c) increases by 2-14 times under random excitations as compared to equivalent harmonic excitations i.e. under same energy input. It is recommended that the energy harvester be used in aerospace structures where random vibration amplitude is higher, to harvest more energy.

This is the final version of the article. Available from the publisher via the DOI in this record. ; This paper presents an envisaged autonomous strain sensor device, which is dedicated to structural health monitoring applications. The paper introduces the ASIC approach that replaces the discrete approach of some of the main modules ; The SMARTER project is supported by European Union under the ERA-Net funding scheme of the FP7 (CHIST-ERA), and in the case of the spaniard partner through MINECO, reference PCIN-2013- 069.

In recent years, low-power wireless sensors with high flexibility, portability and computing capability have been extensively applied in areas such as military, medicine and mechanical equipment condition monitoring. In this paper, a novel symmetrical T-shaped trapezoidal micro piezoelectric energy harvester (STTM-PEH) is proposed to supply energy for wireless sensors monitoring the vibrations of mechanical equipment. Firstly, the finite element model (FEM) of the STTM-PEH is established. Secondly, the modal analysis of the T-shaped trapezoidal piezoelectric cantilever beam is carried out by finite element software and its vibration modes are obtained. Additionally, the structural characteristics of the STTM-PEH and the composition of piezoelectric patches are described. Furthermore, the effects of resistance, acceleration coefficient, substrate materials and structural parameters of the output performance of the STTM-PEH are researched. The results indicate that the output power of the STTM-PEH rises first and then falls with a change in resistance, while the output voltage does not increase as resistance increases to a certain extent. Meanwhile, selecting copper as the piezoelectric material of the T-shaped trapezoidal piezoelectric cantilever beam can generate a higher energy output. Finally, how the structural parameters, including piezoelectric patch thickness, substrate thickness and cantilever head length, affect the output performance of the STTM-PEH is studied, which illustrates that the load range of the STTM-PEH can be appropriately broadened by adjusting the length of the cantilever beam head. This research is valuable for designing a novel high performance piezoelectric energy harvester.

In this study, the external load resistance of a magnetically coupled two-degree-of-freedom bistable energy harvester (2-DOF MCBEH) was optimized to maximize the harvested power output, considering the third-harmonic distortion in forced response. First, the nonlinear dynamic analysis was performed to investigate the characteristics of the large-amplitude interwell motions of the 2-DOF MCBEH. From the analysis results, it was found that the third-harmonic distortion occurs in the interwell motion of the 2-DOF MCBEH system due to the nonlinear magnetic coupling between the beams. Thus, in this study, the third-harmonic distortion was considered in the optimization process of the external load resistance of the 2-DOF MCBEH, which is different from the process of conventional impedance matching techniques suitable for linear systems. The optimal load resistances were estimated for harmonic and swept-sine excitations by using the proposed method, and all the results of the power outputs were in excellent agreements with the numerically optimized results. Furthermore, the associated power outputs were compared with the power outputs obtained by using the conventional impedance matching technique. The results of the power outputs are discussed in terms of the improvement in energy harvesting performance. ; Published version ; This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korean Government (MSIT) (No. NRF-2019R1C1C1009732). This work was also supported by the BK21+ Program of the National Research Foundation of Korea (NRF) grant funded by the Ministry of Education (MOE).