Suchergebnisse

76 90 199 ; S ; [EN] The influence of internal nozzle flow characteristics over ignition delay, and flame lift-off of reacting direct-injection sprays is studied experimentally for three fuels using two different nozzle geometries. This is a continuation of previous work by the authors, where, evaporative and non-evaporative, isothermal spray developments were studied experimentally for the same nozzle geometries and fuels. Current study reports the ignition delay through Schlieren technique, and flame lift-off length through OH* chemiluminescence visualization. The nozzle geometries consist of a conical nozzle and a cylindrical nozzle with 8.6% larger outlet diameter when compared to the conical nozzle. The three fuels considered are n-heptane, n-dodecane and a three-component surrogate to better represent the physical and chemical properties of diesel fuel. Reacting spray is found to penetrate faster than non-reacting spray due to combustion induced acceleration after ignition. Higher oxygen concentration, and ambient temperature enhance the reactivity leading to higher spray tip penetration. Injection pressure does not affect the reactivity significantly and hence, influences spray penetration through momentum-similar to a non-reacting spray. Both ignition delay and lift-off length are found to be shortest and longest for n-dodecane and n-heptane, respectively, while the surrogate fuel falls in-between the two pure component fuels. Both ignition delay and lift-off length are found to decrease with increase in oxygen concentration, ambient temperature, and density. The cylindrical nozzle, in spite of shorter lift-off length is found to have longer ignition delay, when compared to the conical nozzle. This could be due to better atomization leading to larger spread angle and evaporative cooling from the cylindrical nozzle compared to a conical nozzle. The longer ignition delay also leads to leaner equivalence ratios at the time of ignition. (C) 2017 Elsevier Ltd. All rights reserved. This work was sponsored by ...

In this study, particle image velocimetry (PIV) measurements have been performed extensively on a non-reactive dense diesel spray injected from a single orifice injector, under various injection pressure and steady ambient conditions, in a constant flow chamber. Details of PIV setup for diesel spray measurement without additional seeding are explained first. The measured velocity profiles are compared to those obtained from other similar measurements performed in a different institution, as well as those obtained from a 1D spray model simulation, presenting in both cases a good level of agreement. In addition, the velocity fields under various injection pressures and ambient densities show the dominant effects of these parameters on the behavior of diesel spray. The self-similarity of the transverse cut profiles of axial velocity is evaluated, showing that the measurements are in agreement with the hypothesis of self-similar velocity profiles. Finally, the effect of injection pressure and ambient density on the velocity fluctuations is presented and analyzed as well. While the experimental results presented here could help to understand the complex diesel fuel-air mixing process during injection, they also provide additional spray velocity data for future computational model validation, following the main idea of the Engine Combustion Network. ; This work was sponsored by "Ministerio de Economia y Competitividad" of the Spanish Government in the frame of the Project "Comprension de la influencia de combustibles no convencionales en el proceso de injeccion y combustion tipo diesel", Reference TRA2012-36932. Additionally, the optical equipment used for the project was purchased with funding from Ministerio de Economia y Competitividad FEDER-ICTS-2012-06. ; Payri Marín, R.; Viera-Sotillo, JP.; Wang, H.; Malbec, L. (2016). Velocity field analysis of the high density, high pressure diesel spray. International Journal of Multiphase Flow. 80:69-78. https://doi.org/10.1016/j.ijmultiphaseflow.2015.10.012 ; S ; 69 ; 78 ...

The influence of internal nozzle flow characteristics over macroscopic spray development is studied experimentally for two different nozzle geometries and three fuels. The measurements include a complete hydraulic characterization consisting of instantaneous injection rate and spray momentum flux measurements, followed by a high-speed visualization of isothermal liquid spray in combination with cylindrical and conical nozzle configurations. Two of the fuels are pure components n-heptane and n-dodecane while the third fuel consists of a three-component surrogate to better represent the physical and chemical properties of diesel fuel. The cylindrical nozzle with 8.6 % larger diameter, in spite of higher mass flow rate and momentum flux, shows slower spray tip penetration when compared to the conical nozzle. The spreading angle is found to be inversely proportional to the spray tip penetration. The spreading angle is largely influenced by the nozzle geometry and the ambient density. Rail pressure was found to have weak influence on the near-field spreading angle and no influence on the standard deviation of the spreading angle. n-Heptane spray shows slowest penetration rates while n-dodecane and the surrogate fuel mixture show very similar spray behavior for variations in injection pressure and back pressure. However, the surrogate fuel mixture shows higher penetration than n-dodecane when using the conical nozzle and lower penetration than n-dodecane when using cylindrical nozzle. ; This work was sponsored by Ministerio de Economia y Competitividad of the Spanish Government in the frame of the Project "Estudio de la interaccin chorro-pared en condiciones realistas de motor", Reference TRA2015-67679-c2-1-R. Additionally, the employed nozzles and diesel surrogate were provided and defined by GM R&D. ; Payri Marín, R.; Viera Sotillo, JP.; Gopalakrishnan, V.; Szymkowicz, PG. (2016). The effect of nozzle geometry over internal flow and spray formation for three different fuels. Fuel. 183:20-33. ...