Suchergebnisse

In this work, we present the correlation between cathode composition and features of the arcing process for Mo1-xCux [x = 0.0, 0.07 (0.05), 0.14 (0.10), 0.21 (0.15), 0.40 (0.3), 0.73 (0.63), 0.97 (0.95), and 1.00, atomic fraction (weight fraction)] cathodes used in a DC vacuum-arc deposition system. It is found that the stability of the arcing process crucially depends on the cathode composition. The most stable arc spot and the lowest cathode potential (similar to 19 V) are detected for the Mo0.27Cu0.73 cathode, while the Mo0.93Cu0.07 cathode shows the most unstable arcing process with the highest cathode potential (similar to 28 V). The properties of the generated plasma are also strongly dependent on the relative ratio of the cathode elements. The metal ions from the Mo and Cu cathodes have peak kinetic energies around 136 and 62 eV, respectively, while for a Mo0.79Cu0.21 cathode, the corresponding energies are only 45 and 28 eV. The average charge states decreased from 2.1 to 1.6 for Mo ions and from 2 to 1.2 for Cu ions. The intensity of macroparticle generation and the size of the droplets correlate with the relative fraction of Cu. However, it is shown that, typically for the cathodes with a low amount of Cu, an increased abundance of visually observed macroparticles leads to droplet-free films. The film thicknesses and their compositions also demonstrate dependencies on the elemental composition of the cathode. These results are discussed in the light of no solubility between Mo and Cu and the high temperature of the cathode surface during the arcing process. Published under license by AIP Publishing. ; Funding Agencies|Knut and Alice Wallenberg (KAW) FoundationKnut & Alice Wallenberg Foundation [KAW 2015.0043]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University (Faculty Grant SFO-Mat-LiU) [2009 00971]; Swedish Research CouncilSwedish Research Council [642-2013-8020]

Herein, we investigate the influence of powder metallurgical manufactured Ti0.5Al0.5 cathode grain size (45-150 mu m) on the properties of a DC arc discharge, for N-2 pressures in the range 10(-5) Torr (base pressure) up to 3x10(-2) Torr. Intermetallic TiAl cathodes are also studied. The arc plasma is characterized with respect to ion composition, ion charge state, and ion energy, and is found to change with pressure, independent on choice of cathode. Scanning electron microscopy, X-ray diffraction, and Energy-dispersive X-ray spectroscopy of the cathode surfaces and the concurrently deposited films are used for exploring the correlation between cathode-, plasma-, and film composition. The plasma has a dominating Al ion content at elevated pressures, while the film composition is consistent with the cathode composition, independent on cathode grain size. Cross-sections of the used cathodes are studied, and presence of a converted layer, up to 10 mu m, is shown, with an improved intermixing of the elements on the cathode surface. This layer is primarily explained by condensation of cathode material from the melting and splashes accompanying the arc spot movement, as well as generated plasma ions being redeposited upon returning to the cathode. The overall lack of dependence on grain size is likely due to similar physical properties of Ti, Al and TiAl grains, as well as the formation of a converted layer. The presented findings are of importance for large scale manufacturing and usage of Ti-Al cathodes in industrial processes. (C) 2019 Author(s). ; Funding Agencies|Swedish Research Council [642-2013-8020]; Knut and Alice Wallenbergs Foundation [KAW 2015.0043]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University (Faculty Grant SFO-Mat-LiU) [2009 00971]

The first Fe-based MAX phase is realized by solid-state substitution reaction of an Fe/Au/Mo2GaC thin-film diffusion couple, as determined by X-ray diffraction and scanning transmission electron microscopy. Chemical analysis together with elemental mapping reveals that as much as 50 at.% Fe on the A site can be obtained by thermally induced Au and Fe substitution for Ga atomic layers in Mo2GaC. One-sixth of the original Ga is also replaced by Au atoms. When annealing Mo2GaC thin films covered with Fe only, the Mo2GaC phase remains intact, that is, Au acts as a catalyst for the substitution reaction. [GRAPHICS] . ; Funding Agencies|Swedish Foundation for Strategic Research (Stiftelsen for Strategisk Forskning, SSF) through the Synergy Grant FUNCASE; Knut and Alice Wallenberg (KAW) Foundation [KAW 2015.0043]; Swedish Research Council (Vetenskapsradet, VR) [621-2012-4425, 642-2013-8020, 2013-4018]; Swedish Government Strategic Research Area (SFO) [2009-00971]

CrB x thin films with 1.90 < x < 2.08 have been deposited by direct-current magnetron sputtering (DCMS) from a stoichiometric CrB 2 target at 5 and 20 mTorr (0.67 and 2.67 Pa) Ar pressure onto sapphire (0 0 01) substrates. All films, irrespective of deposition conditions, exhibit a (0 0 01) texture. Attesting to the achievement of close-to-stoichiometric composition, epitaxial film growth is observed at 900 ?C, while film growth at 500 ?C yields (0001) fiber texture. Film composition does not depend on substrate temperature but exhibits slightly reduced B content with increasing pressure for samples deposited at 900 ?C. Excess B in the overstoichiometric epitaxial CrB 2.08 films segregates to form B-rich inclusions. Understoichiometry in CrB 1.90 films is accommodated by Cr-rich stacking faults on { 1 1? 00 } prismatic planes. ? 2021 The Author(s). Published by Elsevier Ltd on behalf of Acta Materialia Inc. This is an open access article under the CC BY license ( http://creativecommons.org/licenses/by/4.0/ ) ; Funding Agencies|Swedish Foundation for Strategic Research (SSF)Swedish Foundation for Strategic Research [EM16-0004, RIF 14-0074]; Knut and Alice Wallenberg (KAW) FoundationKnut & Alice Wallenberg Foundation [KAW 2015.0043]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University [200900971]; KAW

This work reports on sputter depositions carried out from a compound (Ti,Zr)(2)AlC target on Al2O3(0 0 0 1) substrates at temperatures ranging between 500 and 900 degrees C. Short deposition times yielded 30-40 nm-thick Al-containing (Ti,Zr)C films, whereas longer depositions yielded thicker films up to 90 nm which contained (Ti,Zr)C and intermetallics. At 900 degrees C, the longer depositions led to films that also consisted of solid solution MAX phases. Detailed transmission electron microscopy showed that both (Ti,Zr)(2)AlC and (Ti,Zr)(3)AlC2 solid solution MAX phases were formed. Moreover, this work discusses the growth mechanism of the thicker films, which started with the formation of the mixed (Ti,Zr)C carbide, followed by the nucleation and growth of aluminides, eventually leading to solid state diffusion of Al within the carbide, at the highest temperature (900 degrees C) to form the MAX phases. ; Funding Agencies|Swedish research council VR-RFISwedish Research Council [2017-00646_9]; Swedish Foundation for Strategic ResearchSwedish Foundation for Strategic Research [RIF14-0053]; Euratom research and training programme 2014-2018 [740415]; Stiftelsen Olle Engkvist ByggmastareSwedish Research Council [184-561]; Knut and Alice Wallenberg FoundationKnut & Alice Wallenberg Foundation [KAW 2015.0043]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University (Faculty Grant SFO-MatLiU) [2009 00971]; Research Foundation FlandersFWO [AKUL/1319]

The magnetic properties of the new phase (Cr0.5Mn0.5)(2)AuC are compared to the known MAX-phase (Cr0.5Mn0.5)(2)GaC, where the former was synthesized by thermally induced substitution reaction of Au for Ga in (Cr0.5Mn0.5)(2)GaC. The reaction introduced a lattice expansion of similar to 3% along the c-axis, an enhancement of the coercive field from 30 mT to 140 mT, and a reduction of the Curie temperature and the saturation magnetization. Still, (Cr0.5Mn0.5)(2)AuC displays similar features in the magnetic field-and temperature-dependent magnetization curves as previously reported magnetic MAX phases, e.g., (Cr0.5Mn0.5)(2)GaC and (Mo0.5Mn0.5)(2)GaC. Thework suggests a pathway for tuning the magnetic properties of MAX phases. (c) 2018 Author(s). All article content, except where otherwise noted, is licensed under a Creative Commons Attribution (CC BY) license. ; Funding Agencies|Swedish Foundation for Strategic Research (Stiftelsen for Strategisk Forskning, SSF) through the Synergy Grant FUNCASE; Knut and Alice Wallenberg (KAW) Foundation [KAW 2015.0043]; Ministry of Education and Science of the Russian Federation [K3-2017-022]; Swedish Research Council (Vetenskapsradet, VR) [621-2012-4425, 642-2013-8020, 2017-03909]; Swedish Government Strategic Research Area (SFO) in Materials Science on Advanced Functional Material (MatLiU AFM) [2009-00971]; DFG [SA 3095/2-1]

In 2017, we discovered quaternary i-MAX phases atomically layered solids, where M is an early transition metal, A is an A group element, and X is C-with a ((M2/3M1/32)-M-1)(2)AC chemistry, where the M-1 and M-2 atoms are in-plane ordered. Herein, we report the discovery of a class of magnetic i-MAX phases in which bilayers of a quasi-2D magnetic frustrated triangular lattice overlay a Mo honeycomb arrangement and an Al Kagome lattice. The chemistry of this family is (Mo2/3RE1/3)(2)AlC, and the rare-earth, RE, elements are Ce, Pr, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm, and Lu. The magnetic properties were characterized and found to display a plethora of ground states, resulting from an interplay of competing magnetic interactions in the presence of magnetocrystalline anisotropy. ; Funding Agencies|Knut and Alice Wallenberg (KAW) Foundation [KAW 2015.0043]; Swedish Research Council [642-2013-8020, 2015-00607, 621-2014-4890]; Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University (Faculty Grant SFO-Mat-LiU) [2009-00971]; DFG [SA 3095/2-1]; IAEC Pazy Foundation Grant; NSF [DMR-1740795]